Schedule Your Service

 

 

What're your ideas with regards to A Step-by-Step Guide to Installing a Bathtub?

Setting up a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is readily obtainable, the task can move quickly; if you have to open a wall surface to eliminate the old bathtub and also place the brand-new bath tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub as well as set in the new one. Make sure you have actually certified on your own for the work and fit trying it. As opposed to employing a specialist to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your washroom if you have actually currently purchased a new bathtub as well as don't need to transform the plan of your previous supply of water pipes.
Your devices as well as material list need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic due to the limited gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Taps

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Mounting the Bathtub

Using the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub until the spirit level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water supply and check all joints as well as new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally check the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the tub must wait up until the tub has been utilized a minimum of once as this will settle it into its final position.

 

 

Preparing for the Installation

Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.

 

 

Tiling Around the Bathtub

In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall in between the bath as well as the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We had been made aware of that report about How to Install a Bathtub Yourself through someone on another domain. Are you aware of anybody else who is in the market for How to Install a Bathtub Yourself? Feel free to share it. Thanks for taking the time to read it.

Try Here